Crivit 1-LD3141 Instrukcja Obsługi
Strona 3
- 9 -
Now the height display will appear
HEIGHT
GROESSE
TAILLE
TAMANO
Set each digit of your height by pressing SEL and confirm each digit by
pressing SET.
Exit setting mode by pressing MODE.
Second time zone
Press and hold SEL for 3 seconds. The watch will switch to the second
time zone display and T2 will appear on the display. Setting the second
time zone can be accomplished in the same way as described in the
previous paragraph.
Press and hold SEL for 3 seconds to return to normal time mode.
Alarm
ALARM
ALARM
ALARM
ALARMA
Press and hold SET for 3 seconds to enter setting mode.
"AL" will appear on the display and the minutes of the alarm time will
blink.
Press SEL to set the minutes and press SET to confirm your setting.
Set the hours in the same way.
You may optionally set the month and day as well.
If neither month nor day are set the alarm will sound daily. If the day is
set, the alarm will sound monthly. If both the month and the day are set
the alarm will sound only at the set date.
The hourly chime setting will now appear on the display
CHIME
STDALARM
SIGN HOR
HORA AL
Press SEL to select a setting and confirm your setting by pressing SET
(ON/EIN/ACTIF/ENCENDID=on,
OFF/AUS/INACTIF/APAGADO=off).
If the chime is activated, the bell symbol will appear and the watch will
chime at the beginning of every hour.
- 10 -
Exit setting mode by pressing MODE.The alarm can be activated or
deactivated by pressing SET. If the alarm is activated the alarm symbol
will appear.
When the alarm sounds, press SET, SEL or MODE to stop the alarm.
Snooze feature
If no button is pressed when the alarm sounds, the alarm will shut off
after 30 seconds and the symbol
will blink on the display. The alarm
will stop and will resume after sounding after 2 minutes. The process
will repeat itself 5 times.
Timer (max. 23:59:00)
TIMER
TIMER
COMPTE
TIMER
Press and hold SET for 3 seconds to enter setting mode.
The minutes of the timer time will blink on the display.
Press SEL to set minutes of the timer time and confirm your setting by
pressing SET. Set the hours in the same way.
Now the additional settings for the timer will follow. Press SEL to select
the desired mode:
Cd r
After reaching 0:00 the timer will count the set time again.
Cd U
After reaching 0:00 the timer will count forward
Cd S
After reaching 0:00 the timer will stop
Exit setting mode by pressing MODE.
The timer can be started or stopped by pressing SET.
Press and hold SET to reset the timer.
After the timer time is up an alarm will sound.
- 11 -
Stop watch
CHRONO
ST-UHR
CHRONO
CRONO
Press SET to start or stop the stop watch. Press SEL while the stop
watch is running to record a lap time. Up to 99 laps can be recorded.
Press and hold SET to reset the stop watch.
Memory feature
DATA
RECALL
ANSICHT
DATEN
APPEL
DONNEES
RECUP
DATOS
Press SEL while the stop watch is stopped to display the fastest lap on
the display. Press SET to display the other lap times.
Please note: The memory feature can only be used if at least one lap
time was recorded.
- 12 -
Heart rate measurement
HRM
PULS
FC
PULSO
The subfeatures of the heart rate measurement can only be used when
the chest belt is connected.
Press SEL to access the subfeatures of the heart rate watch.
Timer
TIMER
TIMER
COMPTE
TEMPORIZADOR
memory feature
MEMORY
SPEICHER
MEMOIRE
MEMORIA
target heart rate
ZONE
BEREICH
ZONE
ZONA
calories, fat burn and BMI
CALORIE
KALORIEN
CALORIES
CALORIAS
fitness
FITNESS
LEVEL
FITNESS
LEVEL
NIV FORM
PHYSIQ
NIVEL
FIT
In the middle row of the display the heart rate is shown while wearing
the chest belt. If the signal is received from the chest belt the heart
symbol will flash. To the right of the heart rate the heart rate in percent
of the maximum heart rate is shown. The maximum heart rate is
calculated by evaluating your age, weight and height.
- 13 -
Warning light
ST/SP
If your heart rate reaches or
exceeds 99% of your maximum
heart rate, or your heart rate
exceeds the target zone values
(see target zone) the red warning
light will blink.
Timer
TIMER
TIMER
COMPTE
TEMPORIZADOR
The bottom row of the display will show the elapsed training time. The
middle row will show your heart rate and the heart rate in percent of the
maximum heart rate.
The timer will start automatically when the chest belt starts measuring
the heart rate. The timer will continue counting the time if the feature
mode of the watch is changed.
Press SET to select the timer mode:
TIMER
total training time
training time in heart rate target zone
▲
training time with heart rate over target zone
▼
training time with heart rate below target zone
Press and hold SET to reset the training time.
- 14 -
Memory feature
MEMORY
SPEICHER
MEMOIRE
MEMORIA
The stored values are shown in the bottom row of the display.
maximum heart rate during training
HI
H
FO
AL
minimum heart rate during training
LO
N
FA
BA
average heart rate during training
AV
D
MO
PR
Press and hold SET to reset the stored values.
Target heart rate
ZONE
BEREICH
ZONE
ZONA
The bottom row of the display will show the lower and upper limit value
of the target zone.
The selected training type is shown on the top row of the display.
L- U
user defined
L-1
Health (50-65% of maximum heart rate)
L-2
Fitness (65-80% of maximum heart rate)
L-3
Performance (80-95% of maximum heart rate)
Press and hold SET for 3 seconds to enter setting mode.
Select the training type by pressing SEL. If "U" is selected (user
defined) the lower and upper limits can be set. Press SET. The display
will show the lower limit.