Samsung LE40C630K1W - Instrukcja (Strona 175)

13
Ελληνικά
03
Βασικ
ά χ
αρακτηριστικ
ά
Satellite System Setup
The PIN input screen appears. Enter your 4 digit PIN
number. Satellite System Setup is available when
Antenna is set to Satellite. Before running Auto Store,
set Satellite System Setup. Then channel scan is run
normally.
Satellite Selection: You can choose the satellites ■
for this TV.
LNB Power (Off / On): Enables or disables the
■
power supply for the LNB.
LNB Settings
■ : Configures the outdoor equipment.
Satellite: Selects the satellite for receiving digital
broadcasts.
Transponder: Selects a transponder from the list or
adds a new transponder.
DiSEqC Mode: Selects DiSEqC mode for the selected
LNB.
Lower LNB Oscillators: Sets the LNB oscillators to a
lower frequency.
Upper LNB Oscillators: Sets the LNB oscillators to a
higher frequency.
Tone 22 khz (Off / On / Auto): Selects the Tone 22
kHz depending on the LNB type. For a universal LNB it
should be Auto.
Signal Quality: Display the current status of
broadcasting signal.
Positioner Settings
■ : Configures the antenna
positioner. Positioner (Off / On): Enables or disables
the positioned control.
Positioner Type (USALS / DiSEqC 1.2): Sets
the positioned type between DiSEqC 1.2 and
USALS(Universal Satellite Automatic Location
System).
My Longitude – : Sets the longitude for my location.
My Latitude – : Sets the latitude for my location.
Satellite Longitude Settings – : Sets the longitude of
user defined satellites.
User Mode: Sets the position of satellite antenna
according to each satellite. If you store the current
position of satellite antenna according to a certain
satellite, when the signal of that satellite is needed,
the satellite antenna can be moved to pre-populated
position.
Satellite – : Selects the satellite to set the position for.
Transponder: – Selects a transponder from the list for
signal reception.
Moving Mode:
– Selects the movement mode
between discrete and continuous movement.
Step Size – : Adjusts the step size degrees for the
antenna rotation. Step Size is available when
Moving Mode is set to Step.
Go to Stored Position
– : Rotates the antenna to the
stored satellite position.
Antenna Position
– : Adjusts and stores the antenna
position for the selected satellite.
Store Current Position
– : Stores current position as
the selected positioner limit.
Signal Quality
– : Display the current status of
broadcasting signal.
Installer Mode: Sets limits to the scope of movement
of satellite antenna or reset the position. Generally,
installation guide uses this function.
Limit Position (East / West) – : Selects the direction
of the positioner Limit.
Antenna Position: – Adjusts and stores the antenna
position for the selected satellite.
Store Current Position:
– Stores the current position
as the selected positioner Limit.
Go to Zero
– : Moves the antenna to the reference
position.
Reset Positioner Limit
– : Allows the antenna to
rotate over the full arc.
Reset All Setting (OK / Cancel) ■ : All satellite settings
will be reset to the initial values.
Επεξεργασία καναλιών ¦
Μενού επιλογών διαχείρισης καναλιών
(στη
Διαχείρ. καναλιών)
1. Επιλέξτε κάποιο κανάλι και πατήστε το κουμπί TOOLS .
2. Τροποποιήστε το όνομα ή τον αριθμό του καναλιού
χρησιμοποιώντας το μενού Επεξεργασία ονόματος
καναλιού ή Επεξ. αρ. καναλιών.
Επεξεργασία ονόματος καναλιού
■ (μόνο για
αναλογικά κανάλια): Εκχωρήστε το δικό σας όνομα
καναλιού.
Επεξ. αρ. καναλιών
■ (μόνο για ψηφιακά κανάλια)
Τροποποιήστε τον αριθμό πατώντας τα επιθυμητά
αριθμητικά κουμπιά.
BN68-02631C_Gre.indb 13 2010-3-3 21:45:47